Lessoon 1: Waveguide Ports
-
Waveguide Port Basics
-
Frequency Dependent Modes(inhomogeneous ports)
-
Mode Polarization
-
Reference Plane-Phase de-embedding
-
Boundary Conditions of Waveguide Port Edges
-
Hexahedral Meshing
-
Multipin Waveguide Ports
Lesson 2: Meshing Overview
-
How to get a Good Mesh?
-
Mesh Types
-
Hexahedral Meshing for Time Domain Simulations
-
Tetrahedral and Surface Meshing for Frequency Domain Simulations
Lesson 3: Antenna Simulation Overview
-
Antenna Magus
-
Antenna Examples in CST Studio Suite
-
Antenna Examples overview
-
Farfield Outputs
-
Farfield Definitions
-
Tips & Tricks for an Accurate Farfield
Project 1: Horn Antenna Simulation
-
Model
-
Workflow using CST Studio Suite
-
New Project Template-Horn Antenna
-
Horn Antenna Construction
-
Simulation Setup
-
Plot Results
-
Parameter Sweep
-
Farfield Post processing
Project 2: Reflector Antenna Simulation
-
Model
-
New Project Template-Reflector Antenna
-
Reflector Antenna Modeling
-
Workflow using System Assembly and Modeling (SAM)
-
Assembly Setup
-
Available Simulation Approaches
-
Hybrid Solver Task
-
Setup Hybrid Solver Task- Bidirectional
-
Advanced : Looped Parameter Sweep
-
Parameter Sweep Task
Project 3: Dual Patch Antenna and Feeding Network
-
Final Model
-
Workflow CST Studio Suite
-
Create a New Template
-
Model the Antenna
-
Define Excitation
-
Visualize Results
-
Combine Results
-
Simultaneous Excitation-Info Slide
-
Microstrip Feeding Network Info
-
Microstrip Feeding Network Modeling
-
S-Parameters Simulation
-
Simulate the Antenna with feeding network and SMA connector
-
Assembly View
-
Create 3D Simulation Project
-
Modify Simulation Project
-
Frequency Domain Solver Run
-
Visualizing Results
Project 4: Patch Antenna Array Design
-
Phased Array workflow using Antenna Magus and the Array Task
-
Synthesize Antenna Inside Antenna Magus
-
Run Exported Model in CST Studio Suite
-
Plot Results
-
Restart Simulation & Plot S-Parameters
-
Decoupling Plane
-
Array Design Introduction
-
Create Array project
-
Array Task
-
Array Task Results
Project 5: Mobile Phone Antenna Design and Integration
-
Workflow Using CST Studio Suite
-
Characteristic Mode Analysis (CMA)
-
Parametric Study using CMA
-
Inclusion of Finite Dielectric
-
Antenna Integration into Housing
-
Meshing, Impedance Matching and Bandwidth Potential
-
Check Global Mesh Settings
-
Start Time Domain Simulation
-
Antenna Matching and Bandwidth Potential
-
Over-the-Air Performance and MIMO Analysis
Project 6: Radio Frequency Identification (RFID) Tag
-
RFID Workflow
-
RFID Model Description
-
RFID Construction
-
Create 3D Simulation Project using SAM
-
3D Model Setup
-
Analyze Results
-
Conformal RFID on 3D Object
-
Conformal RFID Model Setup
-
Transient Solver Simulation
-
Analyze Results
-
S-Parameter Comparison- Planer vs. Bent RFID
-
RFID Bending on Phantom Hand Setup
-
Transient Solver Simulation
-
View Results
-
Calculate and Visualize SAR
RFID READER
-
PATCH Antenna
-
Circularly Polarized Patch Antenna
RFID Tag Antennas
-
Dipoles and Derivatives
-
Wiggling Wires
-
Match with meander
-
Getting Loaded
-
Fat and Thin
